Guide to Setting Up Your Foscam Camera Wirelessly

Once you have the Foscam IP Camera setup and connected via ethernet/network cable, please follow the steps below to set it up wirelessly:

1) Most importantly, ensure you are running your wireless network on the 802.11/bg standard. 802.11/b and 802.11/g will also work, but not 802.11/n. However, all 802.11/n routers are backwards compatible with bg/b/g networks. Please refer to your router’s manual on how make this setting change if necessary.

2) Find and note down the following information about your wireless network:

  1. SSID;
  2. Encryption method (e.g., WPA/WPA2/WEP);
  3. Encription technique (e.g., TKIP/AES/TKIP-AES)
  4. Share key

To find the above information you need to log in to your wireless router. To do this enter the IP address of your router into your browser and press enter. You will be prompted to enter your router username and password. If you do not know the IP address of your router you can view it in IP CAMERA TOOLS by selecting and right clicking on your camera, selecting “Network Configuration”, and noting down the “Default Gateway” IP address. This Default Gateway IP address is the the IP address of your router.

Foscam Tools

If you cannot figure out your username, password or the IP address of your router, refer to your router’s manual. If you don’t have the manual on hand, you can obtain a list of default router IP addresses, usernames and passwords by going to our blogpost here.

Once logged in to your router look for an option called “Wireless Settings” or “Wireless LAN”. Once in the Wireless Settings look for and jot down what you have for the setting called “SSID”. Next, look for the setting “Wireless Mode” and make sure it is set to 806.11/bg, 806.11/g, or 806.11/b

Foscam ssid example

Next, look under the “Security Settings” under “Wireless Settings’ and jot down the “Encryption Method”, “Encryption Technique” and the “Shared Key”.

routere example

3) Once you have the information about your network listed in step 2, log in to your camera while it is connected with the ethernet cable. To do this, open IP camera tools and double click on your camera, or enter your camera’s local IP address into your broswer. On the login page, enter the username and password for the camera (default username: “admin” / password: ” ” – leave password blank) and press “Login”.

You will notice that there are two “Login” buttons. If you are using IE, press the first “Login” button.
If you are using Firefox or Chrome, use the second “Login” button.

4) Once logged in to the Camera, look on the left panel and click on the option “For Administrator” (if using IE) or “Device Management” (if using Firefox or Google Chrome”). Then click on “Wireless Lan Settings”. Here, check the box next to “Using Wireless Lan”. Then, enter your “SSID”. Then, select your “Encryption” which is going to be (e.g., WPA/WPA2/WEP together with either TKIP/AES/TKIP-AES). Next, enter your “Shared Key”. Click “Submit” and let the Camera Reboot. Wait 30 seconds and then remove the ethernet/network cable.

Foscam IP Camera Monitoring System

If you are having trouble, set your wireless Encryption Method to WPA and your encryption technique to TKIP. I seem to have the best results using those settings.

5) Give the camera about 30 to 45 seconds to start up and you should start to see the green led on the front flashing much faster than. Open IP camera tools and the camera should appear. Once your camera goes wireless your camera will receive a new IP Address, you will need to use this new IP Address when setting up port forwarding. Now that you have the Wireless Setup working on your Foscam IP Camera, then you can go on to the next tutorial which shows you how to setup your Foscam so that it is accessible from anywhere on the internet.

Please continue on to the Guide To Setting Up Port Forwarding for Viewing Your Foscam Wireless Camera Over the Internet

TAG: Foscam Camera Wireless, foscam camera wireless setup

This entry was posted in Foscam IP Camera User Manual. Bookmark the permalink.

2 Responses to Guide to Setting Up Your Foscam Camera Wirelessly

  1. jose sa says:

    dear sirs
    having my foscam working in my wireless lan at home ,I woul like to transfer to my boat served by aWIFI long range supplied by marina.
    in the boat I do not have a ethernet connection to the camera for the wireless settings (ex scan and find the best wifi)
    I can I do that :acsses the camera for management ?
    thanks

  2. admin says:

    You can first get SSID,Encryption method (e.g., WPA/WPA2/WEP); Encription technique (e.g., TKIP/AES/TKIP-AES)
    Share key from marina and then configure the IP camera accordingly at home. You can get it work in the boat